Summit BIM70 Manual do Utilizador

Automatic Ice Maker User's Manual Be sure unit is standing upright 24 hours prior to plug-in. Model: BIM

9 • To ensure proper ventilation for your ice maker, the front of the unit must be completely unobstructed. Allow at least 101 mm (4”) clearance a

10Electrical Requirements Electrical Shock Hazard Plug into a grounded 3-prong outlet. Never remove the grounding prong from the plug.

11 Leveling the Ice Maker It is important for the ice maker to be leveled in order to work properly. It can be raised or lowered by rotating the

12Nut of water draining hole Connecting the water line: 1. Turn off main water supply. Turn on nearest faucet long enough to clear the line of wat

13NOTE: The drain hose should never be allowed to hang or loop higher than the bottom of the ice storage bin. 3. All horizontal runs of drain lin

14OPERATION Final Check List before Operation 1. Have all packing materials and tape been removed from the interior and exterior of the ice maker?

15 Operating Method 1. Switch on the Power switch on the right side panel. The light will be on. The ice maker will start working automatically

16 Harvest: During the harvest cycle the compressor is still operating, but the water pump has stopped. Two other components have been energized: t

17 ● Water running from the water sump to the evaporator plate may make a splashing sound. ● Water running from the evaporator to the water sump

18 CLEANING AND MAINTENANCE If the ice maker is left unused for a long time, before the next use it must

Table of Contents Page ICE MAKER SAFETY ... 2 IMPO

19Exterior Cleaning The door and cabinet may be cleaned with a mild detergent and warm water solution such as 1 oz of dishwashing liquid mixed with

20 Interior Cleaning The ice storage bin should be sanitized occasionally. Clean the bin before the ice maker is used for the first time and reused

21 2. Take out the row of flake covers by snapping one end up and pulling forward. 3. Remove the slideway from the water sump.

22 6. Wipe down the interior of the water sump with the de-scaling solution and warm water. Rinse thoroughly with clear water. 7. Reassemble t

23 5. Allow 30 minutes for proper cleaning. After cleaning, shut off the power switch, and unscrew the nut of the water-draining hole on the rear

24 Control Box (behind front cover) Descriptions of LEDs and buttons: 1. Red LED: Ice Full indicator light. When

255. Mode button: Mainly for service. When this button is pressed, unit can change from Ice Making mode to Ice Harvest mode, or from Ice Harvest

26 MAJOR FUNCTIONS 1. Completely automatic operating procedure. 2. When the ice storage bin is full of ice cubes, the machine stops working au

27 TROUBLESHOOTING Before Calling for Service If the unit appears to be malfunctioning, read through the Operation section of this manual first.

28

2 ICE MAKER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and

29 LIMITED WARRANTY PARTS AND LABOR WARRANTY INFORMATION SUMMIT appliances are manufactured to provide outstanding value, and your satisfaction is

30of any parts that SUMMIT determines have been subjected after the date of manufacture to alteration, neglect, abuse, misuse, accident, damage duri

31 Tested and certified to NSF standard 12 by NSF International Probado y certificado por NSF International de acuerdo con la norma N

3 IMPORTANT SAFEGUARDS Before the ice maker is used, it must be properly positioned and installed as described in this manual, so read the manua

4  The ice maker should not be located next to ovens, grills or other sources of high heat.  The ice maker must be installed with all electrica

5plug firmly and pull straight out from the outlet. Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do n

6 INTRODUCTION This SUMMIT Ice Maker finds wide application in households, bars, restaurants, hotels, supermarkets, etc. This unit produces cr

7 COMPONENT LOCATIONS Door Ice cube full sensor Front cover Ventilation louvers Leveling caster Control box (behind front

8 ICE MAKER INSTALLATION Unpacking Excessive Weight Hazard Use two or more people to move and install ice maker. Failure to do so can resul